• Monday – Friday: 08:30 am – 05:00 pm | Closed Saturday & Sunday

    Pool and Spa Lift Manuals

    Pool & spa lift documentation

    Two kinds of pool lift. They break in completely different ways.

    Every pool lift manual we hold, in one place. Before you troubleshoot, work out which kind you have — an Aqua Creek runs on a battery and will tell you when it is flat, while an Aquatic Access has no electricity in it at all and runs on your household water pressure. Almost every “my pool lift stopped working” call comes down to that difference.

    See all 16 documents
    Aqua Creek · Aquatic Access · free manufacturer PDFs, no form to fill in

    Which kind do you have?

    • Aqua CreekBattery powered, with a charger
    • Aquatic AccessWater powered, no electricity
    • Beeping liftAqua Creek only — it is the battery
    • Weak or slow liftAquatic Access — check water pressure

    Aqua Creek: if it is beeping, that is the battery talking

    The beep is not a fault light coming on — these lifts deliberately sound an audible alarm when the battery runs low, so a beeping lift is the lift doing its job. Charge the battery, and if it will not hold a charge, replace it.

    If you want to check before buying a battery, you can measure it with a multimeter set to DC. A healthy pack reads about 24 volts or higher. A reading that comes back negative means the leads are on the wrong terminals — swap the probes and read it again before condemning the battery.

    Grinding, popping or jerky movement is different, and it is not a wait-and-see. Noise like that from the actuator means the lift should come out of service until someone qualified has looked at it. A pool lift is holding a person over water; this is the one symptom not to ride out.

    Aquatic Access: water pressure is the whole story

    These lifts have no motor, no battery and no charger — they run on city or household water pressure. That makes them wonderfully simple, and it also means every performance complaint traces back to pressure.

    Specifically, they work best at roughly 55 to 65 PSI. If yours feels slow or weak, measure the pressure at the supply before assuming the lift is faulty; an inexpensive screw-on gauge from a hardware store is enough. If your static pressure is above 70 PSI, you need a pressure reducer fitted — too much is a problem in its own right, not a bonus.

    Because there is nothing electrical in the lift, a power cut does not stop it. That is a genuine advantage worth knowing if you are still choosing between the two.

    Every pool and spa lift document we hold

    Aqua Creek

    ModelDocumentFile
    Ranger 2Installation & operationDownload PDF
    NeptuneInstallation & operationDownload PDF
    AdmiralInstallation & operationDownload PDF
    Mighty 400Installation & operationDownload PDF
    Power EZ 2Installation & operationDownload PDF
    Ranger 2Spec sheetDownload PDF
    NeptuneSpec sheetDownload PDF
    AdmiralSpec sheetDownload PDF
    Mighty 400Spec sheetDownload PDF
    Power EZ 2Spec sheetDownload PDF

    Aquatic Access

    ModelDocumentFile
    above-ground pool liftInstructionsDownload PDF
    above-ground pool liftSizing worksheetDownload PDF
    IGAT-180Installation manualDownload PDF
    IGAT-180 ADInstallation manualDownload PDF
    IGAT-90Installation manualDownload PDF
    IGMTInstallation manualDownload PDF

    Related pages

    The lifts we stock and install are on our pool & spa lifts page — including the Ranger 2, the Neptune and the Aquatic Access in-ground range.

    Pool lift batteries and service in East Texas

    We supply and install pool and spa lifts across Tyler, Waco and the surrounding communities, and we carry batteries for the Aqua Creek range. If yours is beeping, running slowly or making a noise you do not like, call us — and if it is the noise, stop using it first.

    Call (903) 592-6760

    Looking for a different document? All 114 we keep on file are on the owner manuals page.

    Compare